Globe Valve Series

Product drawing»

Structural drawing»

News > News Detail

Globe Valve Cv Value Calculation and Selection: Sizing Formulas and Practical Guidance

2026-11-18

Globe valves have a significantly lower Cv than ball or gate valves of the same nominal size, and the rated Cv must be matched to the calculated requirement with the correct margin for stable control.The main globe valve product names of China globe Valve Network include:DIN Angle-type Bellows Globe Valve,Electric Flange Straight-through Globe Valve,External Thread Ammonia Globe Valve,Electric Cast Steel Self-sealing Tightly Globe Valve,Flange,Welding Water Sealing Globe Valve,Flange Straight-through Copper Globe Valve,Forged SteelStraight-through Globe Valve,Flange Straight-through Ammonia Globe Valve.

What Cv means. Cv is defined as the number of US gallons per minute of water at 60°F that flows through a fully open valve with a pressure drop of 1 psi. Kv is the metric equivalent: cubic meters per hour of water at 1 bar pressure drop, with the conversion Kv = 0.865 × Cv.

Liquid sizing formula. For clean, non-vaporizing liquids, the required Cv is:

Cv = Q × √(SG / ΔP)

where Q is flow in GPM, SG is specific gravity (water = 1), and ΔP is pressure drop in psi. In metric units, Cv = 11.6 × Q × √(SG / ΔP) with Q in m³/h and ΔP in kPa. When ΔP exceeds approximately half the margin above vapor pressure, cavitation or flashing may occur, and the calculation must be corrected for choked flow.

Gas sizing formula. For gases below the choked-flow limit (ΔP < 0.5 × P1), the required Cv is:

Cv = Q / (963 × √(ΔP × (P1 + P2) × G / TR))

where Q is flow in SCFH, P1 and P2 are absolute pressures in psi, G is gas specific gravity relative to air, and TR is absolute temperature in Rankine. When ΔP exceeds 0.5 × P1, the flow is choked, and a dedicated choked-flow equation must be used.

Steam sizing. For saturated steam under critical (choked) flow, Cv = m / (1.61 × p1), where m is steam flow in lb/hr and p1 is inlet absolute pressure in psia. For non-critical flow, Cv = m / (2.1 × √((p1 + p2) × dp)). Superheated steam requires a correction factor: Cv = Cv_saturated × (1 + 0.00065 × dT), where dT is the degree of superheat in °F.

Selection procedure and safety margin. Calculate the required Cv, then select a valve whose rated Cv is approximately 1.3 to 1.5 times the calculated value, so that the valve operates at 70 to 80 percent opening under normal flow. A valve selected at exactly the calculated Cv will be oversized in effective terms only at maximum flow and will operate too close to its seat at normal flow, causing instability and accelerated wear. Oversizing beyond this margin also harms controllability, because the valve runs at low openings with increased dead band.

Common selection errors. The most frequent mistake is selecting by pipeline diameter instead of calculated Cv. Using a liquid equation for gas service produces dangerously undersized valves. Failing to check choked flow in high-pressure-drop gas or steam service leads to capacity shortfalls. And ignoring cavitation in liquid service destroys trim within hours.

Summary. Globe valve Cv selection follows a defined sequence: calculate the required Cv using the formula for the fluid phase, apply correction factors for choked flow or superheat where applicable, and select a valve with a rated Cv 1.3 to 1.5 times the calculated value so it operates in its controllable range. Avoid selecting by pipe size, never use a liquid equation for compressible fluids, and always check for choked flow and cavitation before finalizing the size.

Do you still need to know or purchase the following globe valve products:

Kaiweixi Valve Group Co., Ltd.
Kaiweixi globe valve Contact Kaiweixi
Zhejiang Shanliu Valve Technology Co., Ltd
Shanliu globe valve Contact Shanliu
Shanghai MeiYan Yi Pump & Valve Co., Ltd.
MeiYan Yi globe valve Contact MeiYan Yi
Shanghai Fengqi Industrial Development Co., Ltd.
FengQi globe valve Contact FengQi